Challenges of the week give artists the opportunity to create new and fantastic art based on a weekly theme set by the challenge moderators. They are also a great place to develop core skills.
Being featured on ConceptArt.org can get your artwork viewed by millions of artists a month including big industry leaders.
|Color and Light||1.1||Do Assignment|
|Color and Light||1.2||Do Assignment||1.3 | 1.4|
|Illusion of Space and Atmosphere||1||Do Assignment|
|Personal Art||1.1||Do Assignment|
This will be my first post and thank you all for knowledge and info you have all posted in the past.I like all the newbies have been just reading and looking.I have a scupley question, i have a basic heat gun from lowes and i was wondering if you can heat up a area in a sculpt and add clay after it was dry or heat up one side and work on another.Heres the piece
So ive detailed the bottom of this skull but didnt want to lay it down to detail the top part as shown.Can i dry the bottom and still work on the top to detail it.
Its very thin.Would the heat go right through to the top and harden?
Im will post any follow up question right away if theres not enough info.Oh and will dry pieces crack off wet clay easily?
Last edited by zuckuss77; April 2nd, 2011 at 10:10 AM.
Any advice would do.I know its a grey area if there was a question of what could happen but any idea would help.Heres a pic of what it is for.
Hi, I use a heat gun to cure polymer clay when I don't want to put in the oven yet. If you are careful, you should be able to harden the finished side enough that it wil have formed a hard 'crust'. But much easier is, as you suggested, to bake the whole thing and add clay to the baked piece later. If possible, roughen the side that needs clay adding to it to give the next later of clay something to adhere to, if not, it should be okay. I created the laser gun for the 1/3 Predator bust I did by baking, adding and rebaking in parts until it was finished.
So it is possible to rebake a project with new clay added without over baking?Will there be any damage?Thanks for the info by the way im was dying over here waiting to hear from someone.thanks again.Is scupley that amazing where you can do more than that?
Yes you can bake and rebake. The only effect it will have is that the older parts that have been baked serveral times will go a dark brown colour, but will be stronger. Sculpey that has just been added will be lighter.
The general advice is to put your sculpture in the oven and bake at around 200 degrees for about an hour and a half, then turn the oven off, and let it cool down, don't take the sculpture out of the oven until its cooled or cracks are more likely to form.
Last edited by Alaneye; April 5th, 2011 at 06:32 PM.
Is the oven better than the heat gun.I figure it would be but i was wondering if the difference is that severe.I do like the heat gun due to quick baking.Looking forward to your predator!!!!!!!!
Are you sure for the temperature? for me it was more around 120 to 130°C.
And for bakeing/re-baking you can add on your already baked piece some white spirit with a paint brush all over the sculpture, this will increase the adhesion of fresh sculpey.
Hi, the instructions say: "Super Sculpey should be cured in a preheated 275 degree F (130 degree C) oven for 15 minutes per quarter inch of thickness."
But many people believe this is too hot and prefer to bake at a lower temperature over a longer period of time claiming the clay cures better.
If you are going to use the original sculpture, rather than making a resin copy, I would definately bake in the oven. The heat gun is good for hardening the sculpey quickly, but it isn't really cured properly and may not last. I've heard it said that if sculpey is not cured properly it tends to crumble over time.
The predator was finished last year. I've posted it here:
Last edited by Alaneye; April 5th, 2011 at 07:17 PM.